借着刷DSL-2740B 3.03新版的机会，把完整的启动信息保存了一下，很长，各位慢看。
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0×2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0×80401000 – 0×80528280 (1208960)
Initialized Data: 0x8041DB50 – 0x8041F980 (7728)
BSS Area: 0x8041F980 – 0×80426280 (26880)
Local Heap: 0×80426280 – 0×80526280 (1048576)
Stack Area: 0×80526280 – 0×80528280 (8192)
Text (code) segment: 0×80401000 – 0x8041DB4C (117580)
Boot area (physical): 0×00529000 – 0×00569000
Relocation Factor: I:00000000 – D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id Name : 96358GW
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:MAC:a1
Ethernet PHY Type : External Switch Using Reverse MII
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xbe800000) …
Code Address: 0×80010000, Entry Address: 0x801ac018
Decompression OK!
Entry at 0x801ac018
Closing network.
Starting program at 0x801ac018
Linux version 2.6.8.1 (root@jie-desktop) (gcc version 3.4.2) #1 Wed Jan 20 18:34:10 CST 2010
Parallel flash device: name AM29LV320MT, id 0×2201, size 16384KB
96358GW prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache…
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 30160k/32384k available (1429k kernel code, 2180k reserved, 215k data, 72k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 … 0x80f00000>
Calibrating delay loop… 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for ‘wait’ instruction… unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe800100
Can’t analyze prologue code at 80173cc4
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
SES: Button Interrupt 0×8025 is enabled
Invalid External Interrupt definition
SES: LED GPIO 0x801a is enabled
Invalid External Interrupt definition
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
OLD policer on
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2010.01.20-10:37+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2010.01.20-10:37+0000) Built-in shell (msh)
Enter ‘help’ for a list of built-in commands.
Loading drivers and kernel modules…
atmapi: module license ‘Proprietary’ taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jan 20 2010 18:32:36
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:MAC:A1
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:MAC:A2
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.18.cpe1.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
app: wlctl country list a > /var/wlclist
app: wlctl country list b > /var/wlclist
eth0 Link UP.
BcmAdsl_Initialize=0xC005D3C8, g_pFnNotifyCallback=0xC0076294
AnnexCParam=0x7FFF7EB8 AnnexAParam=0×00000981 adsl2=0×00000000
pSdramPHY=0xA1FFFFF8, 0×0 0×0
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0×00000981 adsl2=0×00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
app: atmctl start –pqs 125
ATM proc init !!!
app: atmctl operate vcc –add 0.0.35 aal5 1 llcencaps –addq 0.0.35 40 1 –addq 0.0.35 40 2 –addq 0.0.35 40 3
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) – 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ADSL G.994 training
ipt_time loading
ADSL G.992 started
app: insmod /lib/modules/2.6.8.1/kernel/net/bridge/netfilter/ebt_iprange.ko
ADSL G.992 channel analysis
==> Bcm963xx Software Version: EU_3.03 <==
app: echo “3″ > /proc/sys/net/ipv4/conf/all/force_igmp_version
app: echo “1″ > /proc/sys/net/ipv4/ip_forward
app: echo “1″ > /proc/sys/net/ipv4/ip_dynaddr
app: echo “1″ > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
app: pvc2684d &
app: echo > /etc/pppmsg
app: brctl addbr br0
app: brctl stp br0 off
app: brctl setfd br0 0
app: ifconfig eth0 up
app: ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 up
app: ifconfig eth0 up 2>/dev/null
app: brctl addif br0 eth0 2>/dev/null
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
app: sendarp -s br0 -d br0
app: sendarp -s br0 -d br0
app: sendarp -s br0 -d eth0
restrieve 1 ok !
restrieve 2 ok !, num = 4
num<WL_NUM_SSID ok !
restrieve 3 ok !
app: wlctl wds none
app: wlctl down
app: wlctl mbss 1
app: wlctl bss -C 0 down
app: wlctl bss -C 1 down
app: wlctl bss -C 2 down
app: wlctl bss -C 3 down
app: wlctl ssid -C 0 ‘*”*”*”*”*”*”*’
Setting SSID “*”
app: ifconfig wl0 down 2>/dev/null
app: ifconfig wl0.1 down 2>/dev/null
app: ifconfig wl0.2 down 2>/dev/null
ADSL link up, interleaved, us=640, ds=3008
app: ifconfig wl0.3 down 2>/dev/null
app: ifconfig wl0 hw ether 00:MAC:A2 2>/dev/null
app: wlctl -i wl0 cur_etheraddr 00:MAC:A2 2>/dev/null
app: ifconfig wl0.1 hw ether 5a:MAC:a3 2>/dev/null
app: wlctl -i wl0.1 cur_etheraddr 5a:MAC:a3 2>/dev/null
app: ifconfig wl0.2 hw ether 5a:MAC:a0 2>/dev/null
app: wlctl -i wl0.2 cur_etheraddr 5a:MAC:a0 2>/dev/null
app: ifconfig wl0.3 hw ether 5a:MAC:a1 2>/dev/null
app: wlctl -i wl0.3 cur_etheraddr 5a:MAC:a1 2>/dev/null
app: wlctl ap 1
app: wlctl -i wl0 closed 0
app: wlctl country GB
Setting country code using abbreviation: “GB”
app: wlctl band b
app: wlctl regulatory 0
app: wlctl radar 0
wlctl: Unsupported
app: wlctl spect 0
app: wlctl channel 3
app: wlctl wpa_cap -C 0 12 2>/dev/null
wlctl: Not Found
app: wlctl wpa_cap -C 1 0 2>/dev/null
wlctl: Not Found
app: wlctl wpa_cap -C 2 0 2>/dev/null
wlctl: Not Found
app: wlctl wpa_cap -C 3 0 2>/dev/null
app: wlctl -i wl0 maxassoc 128
app: wlctl gmode Performance
app: wlctl gmode_protection_override 0
app: wlctl gmode_protection_control 0
app: wlctl nmode 0; wlctl gmode 1; wlctl nmode 1
wlctl: Bad Band
app: wlctl rate 0 ;wlctl bg_rate 0 ;
app: wlctl mrate -1 ;wlctl bg_mrate -1 ;
app: wlctl rateset default
app: wlctl rtsthresh 2347
app: wlctl fragthresh 2346
app: wlctl dtim 1
app: wlctl bi 100
app: wlctl wme 0
app: wlctl afterburner_override 0
app: wlctl frameburst 1
app: wlctl -i wl0 ap_isolate 0
app: wlctl -i wl0 wme_bss_disable 0
app: wlctl wds none
app: wlctl pwr_percent 60
app: wlctl -i wl0 mac none
app: wlctl -i wl0 macmode 2
app: wlctl -i wl0 mac 00:18:41:57:67:29
app: wlctl -i wl0 mac 00:17:F2:42:1D:31
app: wlctl lazywds 0
app: wlctl wds
app: wlctl up
app: wlctl antdiv 3
KLOB extended to 2 pools
app: wlctl txant 3
app: wlctl csscantimer 0
app: wlctl rmwep -C 0 0
app: wlctl rmwep -C 0 1
app: wlctl rmwep -C 0 2
app: wlctl rmwep -C 0 3
app: wlctl rmwep -C 1 0
app: wlctl rmwep -C 1 1
app: wlctl rmwep -C 1 2
app: wlctl rmwep -C 1 3
app: wlctl rmwep -C 2 0
app: wlctl rmwep -C 2 1
app: wlctl rmwep -C 2 2
app: wlctl rmwep -C 2 3
app: wlctl rmwep -C 3 0
app: wlctl rmwep -C 3 1
app: wlctl rmwep -C 3 2
app: wlctl rmwep -C 3 3
app: wlctl wsec -C 0 0
app: wlctl wsec_restrict -C 0 0
app: wlctl wpa_auth -C 0 0
app: wlctl eap 0
app: wlctl auth -C 0 0
app: wlctl bss -C 0 up
app: wlctl bss -C 1 down
app: wlctl bss -C 2 down
app: wlctl bss -C 3 down
app: ifconfig wl0 up
app: ifconfig wl0 up 2>/dev/null
app: brctl addif br0 wl0 2>/dev/null
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
app: sendarp -s br0 -d br0
startServices@4674 m_wlVar.wlEnbl=[1] wlInitDone=[0]
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 -f &
app: pvc2684ctl -a -v 0.0.35 -f &
pvc2684d: Interface “nas_0_0_35″ created sucessfully
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
app: ifconfig nas_0_0_35 down
app: ifconfig nas_0_0_35 hw ether 00:MAC:a3
app: ifconfig nas_0_0_35 up
app: brctl addif br0 nas_0_0_35
device nas_0_0_35 entered promiscuous mode
br0: port 3(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 3(nas_0_0_35) entering forwarding state
app: sendarp -s br0 -d br0
app: brctl delif br0 eth0 2>/dev/null
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
app: sendarp -s br0 -d br0
app: ifconfig eth0 up 2>/dev/null
app: ethctl eth0 vport query 2>/var/vcfgerr
app: rm /var/vcfgerr
app: insmod /lib/modules/2.6.8.1/extra/vnet.ko
eth0.2: MAC Address: 00:MAC:A1
eth0.3: MAC Address: 00:MAC:A1
eth0.4: MAC Address: 00:MAC:A1
eth0.5: MAC Address: 00:MAC:A1
app: ifconfig eth0.2 up
app: ifconfig eth0.3 up
app: ifconfig eth0.4 up
app: ifconfig eth0.5 up
app: ifconfig eth0 up 2>/dev/null
app: brctl delif br0 wl0 2>/dev/null
device wl0 left promiscuous mode
br0: port 2(wl0) entering disabled state
app: sendarp -s br0 -d br0
app: ifconfig wl0 up 2>/dev/null
app: ifconfig eth0 up 2>/dev/null
app: ifconfig wl0 up 2>/dev/null
app: brctl addif br0 wl0 2>/dev/null
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.2 up 2>/dev/null
app: brctl addif br0 eth0.2 2>/dev/null
device eth0.2 entered promiscuous mode
br0: port 2(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.2) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.3 up 2>/dev/null
app: brctl addif br0 eth0.3 2>/dev/null
device eth0.3 entered promiscuous mode
br0: port 4(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.3) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.4 up 2>/dev/null
app: brctl addif br0 eth0.4 2>/dev/null
device eth0.4 entered promiscuous mode
br0: port 5(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 5(eth0.4) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.5 up 2>/dev/null
app: brctl addif br0 eth0.5 2>/dev/null
device eth0.5 entered promiscuous mode
br0: port 6(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 6(eth0.5) entering forwarding state
app: sendarp -s br0 -d br0
startServices@4674 m_wlVar.wlEnbl=[1] wlInitDone=[1]
app: sntp -s time.nist.gov -s time.windows.com -t “Beijing, Chongquing, Hong Kong, Urumqi” &
app: rtpd
sntp: host not found
app: pppd -c 0.0.35.1 -i nas_0_0_35 -u * -p * -f 0 -o 10800 -m 00e0fcb16e54/2ed9 -t 1492 &
br0: port 2(eth0.2) entering disabled state
br0: port 4(eth0.3) entering disabled state
br0: port 5(eth0.4) entering disabled state
app: iptables -t nat -F DNS_RELAY
app: iptables -t nat -A DNS_RELAY -i br0 -d 192.168.1.1 -p udp –dport 53 -j DNAT –to 128.9.0.107
app: iptables -t nat -A DNS_RELAY -j RETURN
app: iptables -t nat -D ENABLE_NAT -o ppp_0_0_35_1 -j MASQUERADE 2>/dev/null
app: iptables -t nat -I ENABLE_NAT -o ppp_0_0_35_1 -j MASQUERADE
app: iptables -t nat -D ENABLE_NAT 2>/dev/null -j RETURN
app: iptables -t nat -A ENABLE_NAT -j RETURN
app: route add default dev ppp_0_0_35_1 2>/dev/null
PPP: PPP0_0_35_1 Start to connect …
Connect: ppp_0_0_35_1 <–> nas_0_0_35
PPP: PPP0_0_35_1 Connection Up.
app: ifconfig ppp_0_0_35_1 mtu 1492 &
app: route add default gw 123.116.224.1 2>/dev/null
app: iptables -F CH_TCPMSS
app: iptables -A CH_TCPMSS -o ppp_0_0_35_1 -p tcp –tcp-flags SYN,RST SYN -j TCPMSS –clamp-mss-to-pmtu
app: iptables -A CH_TCPMSS -i ppp_0_0_35_1 -p tcp –tcp-flags SYN,RST SYN -j TCPMSS –clamp-mss-to-pmtu
app: iptables -A CH_TCPMSS -j RETURN
app: echo > /proc/net/ip_conntrack
app: echo “4096″ > /proc/sys/net/ipv4/ip_conntrack_max
app: iptables -t nat -D ENABLE_NAT -o ppp_0_0_35_1 -j MASQUERADE 2>/dev/null
app: iptables -t nat -I ENABLE_NAT -o ppp_0_0_35_1 -j MASQUERADE
app: iptables -t nat -D ENABLE_NAT -j RETURN 2>/dev/null
app: iptables -t nat -A ENABLE_NAT -j RETURN
app: iptables -t nat -F DNS_RELAY
app: iptables -t nat -A DNS_RELAY -i br0 -d 192.168.1.1 -p udp –dport 53 -j DNAT –to 202.106.46.151
app: iptables -t nat -A DNS_RELAY -j RETURN
app: /bin/dnsprobe &
app: upnp -L br0 -W ppp_0_0_35_1 -D
Primary DNS server = 202.106.46.151
Secondary DNS server = 202.106.195.68
app: iptables -t filter -I OUTPUT -o ppp_0_0_35_1 -d 239.255.255.250 -j DROP 2>/dev/null
app: iptables -A VRTSRV -j RETURN;iptables -t nat -A NAT_VRTSRV -j RETURN
sntp: time setup successfully
RTNETLINK answers: Invalid argument
HTB init, kernel part version 3.17
HTB init, kernel part version 3.17